Key takeaways
- Learn how to choose an engine hoist for your garage, from boom capacity and reach to folding storage, with five 2-ton folding cranes compared.
An engine hoist, also called a shop crane or cherry picker, lifts an engine out of the bay so you can rebuild it, swap it, or pull the transmission with it. For a home garage, the usual choice is a folding hydraulic crane rated for 2 tons, and that simple sentence hides the one trap that catches almost every first-time buyer: the headline capacity only applies at the shortest boom position. Extend the boom to reach over a fender and the safe load can drop to a quarter of the headline number. This guide explains how to read the load chart, measure your bay, and pick a crane that fits your garage.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
For most home garages, the Torin Big Red T32001 is the safest first choice: a proven 2-ton folding crane with an 8-ton ram and four boom positions, sold through several large retailers. Buyers who want a leveler included should look at the VEVOR 2-1 EHL, while the Dragway Tools LD-E03012 suits those who want a US-made frame built from thick steel.
How to Choose an Engine Hoist for Your Garage
Read capacity at the boom position, not the headline
A 2-ton hoist lifts 4,000 pounds only with the boom fully retracted. A typical four-position boom is rated 4,000 pounds at the shortest setting, then 3,000, 2,000, and 1,000 pounds as it extends. Weigh the engine with its accessories attached, add the transmission if you plan to pull them together, and match that total to the capacity at the boom length you need. The load chart decal on the boom is the authority, not the headline on the box.
Measure reach against your bay
Folding cranes in this class offer roughly 38 to 57 inches of reach, and the hook must clear the front of the car while the legs straddle the bumper. Measure from the front of the vehicle to the center of the engine, then add room for the legs to slide under the car. If the legs cannot get under the vehicle, the crane cannot lift straight up, and the load will swing toward the mast.
Check the folded footprint before you buy
A folded 2-ton crane is still a large piece of steel, and models differ in how flat they fold. Some cranes fold the legs and mast down to a slab that leans against a wall, while others only fold the legs and still occupy a corner of the garage.
Look at the casters and the floor
Six swivel casters are the norm for a 2-ton folding crane. The crane must roll smoothly with a suspended load so you can pull the engine clear of the bay and set it down on a stand. A smooth, level concrete floor is the right surface; gravel, dirt, or a slope make a loaded crane hard to control and easy to tip.
Judge the ram and the frame
An 8-ton ram is the common size on 2-ton cranes, giving a comfortable margin over the rated load. A ram that leaks down under load is a hazard, so choose a crane with a replaceable ram and a parts supply. The frame should be welded steel with a powder-coat finish and tight boom pin holes.
Decide whether you need a leveler
An engine leveler hangs from the hook and lets you tilt the engine as it comes out, which helps it clear the firewall or transmission tunnel. A leveler is worth having for engine-and-transmission pulls, but its own load limit is lower than the crane limit, so the leveler becomes the limit for the combined load.
Think about assembly weight
A 2-ton folding crane weighs roughly 130 to 185 pounds in the box, and assembly takes two people or a careful solo session. Assemble it where you plan to use it, since it is awkward to move up steps or into a truck bed.
Torin Big Red T32001 2-Ton Folding Engine Hoist
The Torin Big Red T32001 is the long-running classic in this class. It is a 2-ton folding shop crane with an 8-ton hydraulic ram and a four-position adjustable boom, rated from 1,000 pounds at full extension up to 4,000 pounds with the boom retracted. The frame is high-tensile steel, the legs fold for storage, and the crane is sold through several large retailers, which makes parts and support easier to find than with a single-seller import. A 2026 buying guide names the T32001 as the crane with the widest retail availability, sold through Amazon, Tractor Supply, and Northern Tool.
Specs:
– Capacity: 2 tons (4,000 pounds) at the shortest boom position
– Hydraulic ram: 8-ton capacity
– Boom: 4 adjustable positions, 1,000 to 4,000 pounds
– Frame: High-tensile steel, folding legs
– ASIN: B000CO9YME
Dragway Tools 2-Ton Folding Hydraulic Engine Hoist LD-E03012
The Dragway Tools LD-E03012 is a US-made folding crane sold for well over a decade. It is rated for 2 tons (4,000 pounds) with four boom positions, and its frame uses 7.8 mm thick steel. The crane lifts to a maximum height of 102 inches with the boom extended and 48 inches with the boom retracted, which gives useful clearance for tall engine bays and truck frames. The tracker record for this listing goes back to 2013, with a third-party offer recorded in February 2026, so the model is still actively sold.
Specs:
– Capacity: 2 tons (4,000 pounds) at the shortest boom position
– Frame: 7.8 mm thick steel, made in the USA
– Boom: 4 adjustable positions
– Maximum lift height: 102 inches extended, 48 inches retracted
– ASIN: B00294B0LS
VEVOR Hydraulic Engine Hoist with Lever 2-1 EHL
The VEVOR 2-1 EHL is the best-equipped crane in this group because it combines the hoist and the leveler in one box. It is a 2-ton (4,400-pound) folding crane with an 8-ton hydraulic pump and an included engine leveler rated for 1,500 pounds, so you can tilt the engine during removal without buying a separate accessory. The listing gives a weight of 157.1 pounds and dimensions of 64.17 by 40.16 by 58.07 inches, so measure your bay before ordering. A tracker recorded the listing in stock and fulfilled by Amazon three days before this guide was written, the freshest availability signal among the five picks.
Specs:
– Capacity: 2 tons (4,400 pounds) at the shortest boom position
– Hydraulic pump: 8-ton capacity
– Leveler: Included, rated 1,500 pounds
– Casters: 6 swivel casters
– ASIN: B0CJ3538Z5
TUFFIOM 2-Ton Folding Hydraulic Engine Crane G33006600
The TUFFIOM G33006600 is a 2-ton (4,400-pound) folding crane with a telescopic boom and outriggers, sold in a yellow finish. The telescopic boom gives a longer reach range than a fixed-step boom, and the outriggers add stability when the legs are spread wide. It is a newer listing, first available in December 2024, and it follows the same formula as the other cranes here: a hydraulic ram, a four-position boom, and a folding frame for storage. The listing record names the product, the model number G33006600, and the ASIN together, which confirms the identity of this exact crane. Because the listing is newer, there is less long-term history to judge it by, so confirm the listing is live and the offer is current before ordering.
Specs:
– Capacity: 2 tons (4,400 pounds) at the shortest boom position
– Boom: Telescopic with outriggers
– Frame: Heavy-duty steel, folding design
– Finish: Yellow
– ASIN: B0DR2MKLW4
Goplus 2-Ton Folding Engine Hoist AT3638BK+
The Goplus AT3638BK+ is a 2-ton (4,000-pound) folding engine hoist with six boom positions, which gives finer steps between the shortest and longest settings than a four-position crane. The frame is high-grade steel, the crane folds for compact storage, and the wheels let you move it around the shop with a load hanging from the hook. A roundup of cherry pickers updated two days before this guide was written still lists the Goplus 2-ton folding hoist as a current pick, so the model remains on the market. One older tracker entry for this exact model notes that it may be out of stock, so treat the availability of this listing as uncertain and confirm the offer is live before ordering.
Specs:
– Capacity: 2 tons (4,000 pounds) at the shortest boom position
– Boom: 6 adjustable positions
– Frame: High-grade steel, folding design
– Casters: 6 iron caster wheels
– ASIN: B01AUG96ZS
Who Should Skip Engine Hoists
An engine hoist is the wrong tool if you only need to pull one engine once. Renting a crane costs less than buying, storing, and assembling a heavy crane for a single weekend job. Skip a purchase if your garage ceiling is too low for the mast at full height, or if the only floor you have is gravel or a sloped driveway, because a loaded crane needs flat concrete to roll safely. Skip the 2-ton class if your engine and transmission together weigh more than the limit at the boom position you must use; a diesel truck engine with its gearbox can exceed it, and the right answer is a larger fixed-frame crane or a professional shop. Never work under a suspended engine. The hoist lifts and moves the load; jack stands and an engine stand hold it.
FAQ
How much can a 2-ton engine hoist lift at full boom extension?
A typical 2-ton folding crane lifts 4,000 pounds only with the boom fully retracted. At full extension the limit commonly drops to 1,000 pounds, with 2,000 and 3,000 pounds at the middle positions. Always match your engine weight to the position you will use, not to the headline number.
Do I need an engine leveler with my hoist?
A leveler is useful when the engine must tilt to clear the firewall or the transmission tunnel, and it is almost essential for engine-and-transmission pulls. A leveler rated for 1,500 pounds becomes the limit for the combined load, so check its load limit separately.
Can I use an engine hoist on a gravel driveway?
A folding shop crane is designed for smooth, level concrete. Gravel, dirt, and slopes make a loaded crane hard to roll and easy to tip, and small casters can sink or catch on uneven ground. Move the vehicle to a flat paved surface before lifting.
How much floor space does a folded engine hoist need?
A folded 2-ton crane still occupies a slab of floor or wall space roughly the size of a large toolbox laid flat, and the mast height when folded can reach your chest. Measure the wall you plan to lean it against, including clearance to walk past, and confirm the legs fold flat enough to fit.
Final Verdict
The Torin Big Red T32001 is the pick for most home garages because it is a proven 2-ton folding crane with an 8-ton ram, a clear four-position load chart, and wide retail availability. Buyers who want the leveler included should choose the VEVOR 2-1 EHL, which bundles a 1,500-pound leveler and was recorded in stock days before this guide was written. The Dragway Tools LD-E03012 is the pick for buyers who want a US-made frame with thick steel and a decade of sales history.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!